美國 Highland Technology
T130單通道皮秒EOM驅動器
- 三個范圍內的可編程延遲和脈沖寬度
- 可編程幅度從 -0.5 伏到 -7 伏到 50Ω 負載
- 上升時間/下降時間 100 皮秒，典型值 (10 – 90%)
- 內置寬度發生器，可調范圍為 250 皮秒至 300 納秒，F(xiàn)WHM
- 內置偏置電源，可調±6V
- +24V DC 供電
- 通過 USB、RS-232 或板載微調器進行控制
- 內置自檢 (BIST)
- 帶有表面安裝法蘭的緊湊型擠壓外殼
- 應用包括：
- 驅動 50Ω 電光相位和幅度調制器
- 在泵浦光纖系統中驅動 50Ω 直接調制種子激光器
- 射頻應用：快速脈沖調制、相移、諧波生成
- 時域器件表征和建模
- 半導體測試
- 系統電纜/正時裝飾
| FUNCTION | Externally-triggered single-channel pulse generator and EOM driver |
| TRIGGER | Rising-edge trigger, 50? input impedance, DC coupled Threshold: +0.5 volts Max safe input: -0.6 volts to +6 volts |
| PROPAGATION DELAY | Range 1: 8ns nominal insertion delay Range 2: 20ns nominal insertion delay Range 3: 70ns nominal insertion delay |
| RF OUTPUT | User adjustable -0.5 volts to -7 volts peak into 50? loads; AC-coupled |
| PULSE RATE | Min pulse rate is 0 Hz Range 1: max 50MHz depending on delay/width settings Range 2: max 25MHz depending on delay/width settings Range 3: max 5MHz depending on delay/width settings |
| RISE/FALL TIMES | 100ps, typ measured at 10/90% |
| PROGRAMMABLE TIMINGS | Range 1 : delay 0 to 5ns width 250ps to 5ns d+w < 5ns Range 2 : delay 0 to 50ns width 500ps to 50ns d+w < 50ns Range 3 : delay 0 to 300ns width 1ns to 300ns d+w < 300ns Ranges are selectable by front-panel DIP switch or remotely |
| JITTER | Range 1: < 3ps RMS typ. Range 2: < 10ps RMS Range 3: < 50ps RMS |
| BIAS SUPPLY | Internal / External DC bias tee injection at RF OUT Internal BIAS supply adjustable ± 6 volts, 100 mA max BIAS connector serves as Hi-Z voltage monitor when set to INT mode |
| CONTROL | Trimpots, RS-232, and USB |
| OPERATING TEMPERATURE | 0 to 50°C, non-condensing |
| STORAGE TEMPERATURE | -20 to 80°C |
| POWER | +24 volts at 250mA, max J24 universal wall-plug power supply furnished |
| COMMUNICATION | USB, RS-232 |
| CONNECTORS | TRIG RF OUT RF MON BIAS OUT SMA jacks Standard B receptacle for USB control, 2.5mm phono jack for RS-232 |
| LED INDICATORS | Green POWER Blue TRIGGER Orange COMM Red ERROR |
| PACKAGING | 4.84″ (L) x 4.06″ (W) x 1.20″ (H) extruded aluminum enclosure |
| CONFORMANCE | OEM product has no UL/FCC/CE compliance requirements Designed to meet UL/FCC/CE requirements |
